Windows PC · Screen Replacement
Windows Laptop Screen Replacement
Cracked glass, black bars, a faint image you can barely read in the dark — a bad laptop screen makes the whole machine feel broken even when everything behind it works. We replace Windows laptop displays on Dell, HP, Lenovo, ASUS, Acer, MSI, and Microsoft Surface, and we match the exact panel your machine was built for instead of guessing.
Most Windows laptops use a standard LCD/LED panel that's quicker and cheaper to swap than an Apple display — but only if it's matched correctly. Touchscreens, 2-in-1 convertibles, gaming panels, and Surface devices are a different story, and we'll tell you which one you have before you spend a dollar past diagnostic.
When you need a screen replacement
- Cracked or shattered LCD — spiderwebbed glass, ink-blot spreading dark spots, or a smashed corner from a drop or a closed-lid object.
- Vertical lines, colored bars, or a frozen band across the image that stays put no matter what's on screen.
- Dim or nearly black display you can only read by shining a flashlight at an angle — usually the backlight circuit or cable, not the panel itself.
- Half the screen black, or a hard split down the middle where one side shows image and the other shows nothing.
- Cracked touchscreen on a 2-in-1 convertible where taps stop registering or the glass is bonded to the panel underneath.
- Flickering, flashing, or image that cuts out when you open and close the lid — a sign of a pinched or failing hinge display cable.
Honest by default
Every device starts with a $65 diagnostic and a written report — exact cost and timeline before we touch it. The fee applies toward your repair.
Cost depends on the panel. A standard non-touch LCD/LED panel is the most affordable swap. A bonded touchscreen or 2-in-1 convertible assembly runs higher, and a glued Surface display is the most involved of all. Higher resolution (1440p, 4K), high-refresh gaming panels (120/144/165Hz), and certain premium brands also drive part cost up. Our $65 written diagnostic confirms exactly which panel and which fault you have — and it applies toward the repair.
Our screen replacement process
Match the exact panel by spec
Windows panels aren't interchangeable by size alone. We read the part number off the back of your original panel and match resolution, refresh rate, connector (eDP pin count and lane layout), backlight, and touch versus non-touch. A 1080p panel won't run in a board wired for 768p, and a 60Hz panel won't drive a 144Hz machine. We order the right one.
Rule out backlight, cable, and GPU first
Not every dark or glitchy screen is the panel. If the image is faintly visible under a flashlight, it's the backlight circuit or display cable. If you see artifacts and lines everywhere — including on an external monitor — the GPU or graphics chip is the real fault, and a new panel won't fix it. We diagnose before we replace.
Replace cleanly — standard, bonded, or Surface
Standard non-touch panels swap quickly with the bezel removed. Touchscreen and convertible displays are bonded glass-and-panel assemblies that take more care and cost more. Surface laptops are heavily glued — the screen is fused like a tablet — so those are a careful, controlled teardown. We do all of this in-house instead of mailing it out.
Test the full display before you get it back
We check brightness across the whole panel, look for dead pixels and backlight bleed in a dark room, confirm touch and pen response where applicable, run the correct refresh rate, and flex-test the hinge cable by opening and closing the lid. You leave with a display that performs like the machine did new.
Why do you need to match the exact panel instead of any screen that fits?
Because physical size is only one of several specs. The resolution, refresh rate, connector pinout, and backlight type all have to match what your laptop's board was built to drive. A panel that looks identical can show no image, the wrong resolution, or flicker if the connector lane layout or refresh rate is off. We read the original part number and match it.
Is my problem the screen or the GPU?
Easy test: plug into an external monitor. If the artifacts, lines, or distortion show up there too, the fault is the GPU or graphics chip, not the panel — a new screen won't fix it. If the external monitor is clean and only the laptop display is bad, it's the panel, cable, or backlight. Our diagnostic settles this for sure before any parts are ordered.
Why does a touchscreen cost more than a regular screen?
Non-touch Windows panels are a single LCD/LED panel that comes off with the bezel. Touchscreens and 2-in-1 convertibles use a bonded assembly where the glass digitizer is fused to the panel, so the part is pricier and the install is more delicate. If you don't need touch and your model supports a non-touch panel, we'll tell you.
Is a Surface screen harder to replace?
Yes. Surface laptops are heavily glued — the display is fused to the chassis like a tablet rather than held by a removable bezel. It's a careful, controlled teardown with managed heat and adhesive, which is why it's more involved and costs more than a standard laptop panel. We handle Surface in-house; many shops mail these out.
Can you replace a high-refresh gaming laptop screen?
Yes, and we match the refresh rate exactly. Gaming laptops ship with 120Hz, 144Hz, or 165Hz panels, and dropping in a 60Hz panel — or the wrong high-refresh panel — means you lose the refresh rate the machine was built for. We source the matching high-refresh panel so you keep the performance you paid for.
How long does it take, and is it warrantied?
Standard non-touch panel swaps are often quick once the matched part is in hand; bonded touch and glued Surface displays take longer. OEM and OLED panels carry a 1-year warranty; aftermarket panels carry 1 month. Walk in at our Clarendon lab in Arlington, or use tracked mail-in from any of the 50 states.
Why WeFixed for your Windows laptop screen
We've spent 11 years doing board-level and microsoldering work, which means we don't reflexively reach for a panel when the real fault is a backlight circuit, a hinge cable, or the GPU. We diagnose first, match the exact panel by spec, and do every part of the job — standard, bonded touch, and glued Surface — in-house instead of mailing your machine to a third party. You get a straight answer, the right part, and an honest call on whether a screen even fixes it. We're an independent lab, and we never sell your data.